Hi all,
I have just been reading through a historical thread about some issues with IPMP.
Some tips from "Peasant" where very useful. Please see below
"Just couple of more hints regarding VM.
For VDS, use one VDS - one guest LDOM, don't put everything in primary-vds.
Disable extended-mappin-space everywhere since i noticed sometimes live migration fails with this on.
You might want to disable INTER-VNET-LINK (to off)
I had a situation when network between two guests, that reside same physical machine on the same subnet, just stops working.
I have ran some internal test with those two options on/off (which should improve network throughput), and didn't notice any performance gains, only experienced issue above
Depends on which patchset you are, perhaps those issues are now fixed.
Regards
Peasant"
The issue I am having is that two Guest LDOMS which have IP addresses in h same subnet/range are unable to ping each other. They can ping all other LDOM Guets, control/ Service etc. but not each other.
Actually, before i switched off INTER-VNET-LINK=off then they would just crash.
We have two IO domains with aggregated ports using IPMP. Please let me know what info you require and I hope you can help. Some details below:
First Guest Domain = Sneezy
primary
MAC
00:10:e0:46:32:e6
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
primary-vsw50 00:14:4f:f9:c0:79 aggr0 0 switch@0 1 1 50 1500 off
------------------------------------------------------------------------------
NAME
secondary
MAC
00:14:4f:fb:51:13
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
secondary-vsw50 00:14:4f:fb:21:17 aggr0 0 switch@0 1 1 50 1500 off
------------------------------------------------------------------------------
NAME
sneezy
MAC
00:14:4f:f8:ce:95
NETWORK
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet0 primary-vsw50@primary 0 network@0 00:14:4f:f9:1a:0b 50 1500 phys-state
vnet1 secondary-vsw50@secondary 1 network@1 00:14:4f:fa:92:25 50 1500 phys-state
admin@martell:/$
Second guest domain on different host= sleepy
admin@lannister:~$ ldm list -o network
NAME
primary
MAC
00:10:e0:46:30:a2
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
primary-vsw50 00:14:4f:fa:c3:20 aggr0 0 switch@0 1 1 50 1500 off
------------------------------------------------------------------------------
NAME
secondary
MAC
00:14:4f:fa:8f:07
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
secondary-vsw50 00:14:4f:f9:a8:69 aggr0 0 switch@0 1 1 50 1500 off
------------------------------------------------------------------------------
NAME
sleepy
MAC
00:14:4f:f8:ce:95
NETWORK
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet0 primary-vsw50@primary 0 network@0 00:14:4f:fa:92:25 50 1500 phys-state
vnet1 secondary-vsw50@secondary 1 network@1 00:14:4f:f9:1a:0b 50 1500 phys-state
admin@lannister:~$ ldm -V
Logical Domains Manager (v 3.1.0.1)
Hypervisor control protocol v 1.11
Using Hypervisor MD v 1.4
System PROM:
Hostconfig v. 1.4.0 @(#)Hostconfig 1.4.0 2014/04/04 17:51
Hypervisor v. 1.13.0.a @(#)Hypervisor 1.13.0.a 2014/04/08 14:05
OpenBoot v. 4.36.0 @(#)OpenBoot 4.36.0 2014/04/04 15:50
Other useful information that may help.
admin@lannister:~$ dladm show-aggr
LINK MODE POLICY ADDRPOLICY LACPACTIVITY LACPTIMER
aggr0 trunk L2 auto active short
admin@lannister:~$ dladm show-vlan
LINK VID OVER FLAGS
aggr5000 50 aggr0 -----
admin@lannister:~$ dladm
LINK CLASS MTU STATE OVER
net0 phys 1500 up --
net1 phys 1500 up --
net2 phys 1500 up --
aggr5000 vlan 1500 up aggr0
aggr0 aggr 1500 up net0 net1
admin@lannister:~$ dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 10000 full ixgbe0
net1 Ethernet up 10000 full ixgbe1
net2 Ethernet up 10000 full vsw0
Many thanks